This is a set of components to move the cord connections on a DaVinci kiln ring to the outer element connection box.

The kit consists of:

1.  (1) Two Pole Terminal
2.  (1) Insulating board
3.  (2) Terminal Mounting Screws (#8 X 3/4" A Type 
4.  (2) #10 SS nuts
5.  (2) #10 SS washers
6.  (2) #10 SS split washers
7.  (1) #10 X 1/2" Self-Tapping screw (ground screw)
8.  (1) #10 star washer (for the ground screw)
9.  (1) Ground Symbol Sticker
10.  (1) 12" length of wire insulator sleaving for covering the cord wires (this gets cut to length to slip over the cord wires)
11.  (2) 8 Gauge 150 Deg C 9" long Power Wires with a ring terminal to go the element connection and a stripped end to go in the new terminal block

12 foot 50 Amp Jumper Cord - Unit is used with DaVinci X3200-D & XB3200-D and T3400-D & TB3400-D Bell-Lift Kilns at 480 Volts and 3 Phase Power. There is no plug on this cord.

50 Amp Jumper Cord with Insulated Sleaving on the ends - Unit is used with DaVinci X2800-D & XB2800-D, X3200-D & XB3200-D, T2300-D & TB2300-D, and T3400-D & TB3400-D Kilns at any Voltage and Phase Power

20 Amp Element Jumper Cord - Unit is 36" Long and used for All Newer Two Section and Three Section Jupiter Automatic and Jupiter Manual Kilns at any Voltage and Phase Power

20 Amp Element Jumper Cord - Unit is 45" Long and used for All Newer Four Section, Five Section, and Pull-Apart Jupiter Automatic and Jupiter Manual Kilns at any Voltage and Phase Power

20 Amp NEMA 5-20P Power Cord - Unit is a 72" Long Cord and can be used at 120 Volts and 1 Phase Power

50 Amp NEMA 6-50P Power Cord - Unit is a 72" Long Cord with a Three Prong Plug and is used with all Easy-Fire Kilns at any Voltage and 1 Phase Power, all J1800 & JD1800, J23 & JD23, and J230 & JD230 Kilns, all Dura-Fire kilns, and many other kilns at any Voltage and 1 Phase Power (Also used for retrofit on Older Econo J1400 Series Kilns)

Used on European version vents, Chameleon, Fuego, Robin and Corona kilns. 15 amp.

Used on UK version vents, Chameleon kilns, Fuego, Robin and Corona kilns. 13 amp.

30 Amp NEMA 10-30P Power Cord - The unit is 12' Long with a Three Prong Plug and can be used with any kiln that is 24 amps or below and is 208 or 240 volts and single phase

30 Amp NEMA 14-30P Power Cord - Unit is 12' Long with a Four Prong Plug and is used with All Liberty-Belle Kilns at any Voltage and 1 Phase Power

50 Amp NEMA 14-50P Power Cord - The unit is 12' Long with a Four Prong Plug and can be used with any kiln that is 48 amps or below and is 208 or 240 volts and single phase

50 Amp NEMA 6-50P Power Cord - Unit is 12' Long with a Three Prong Plug and can be used with any kiln that is 48 amps or below and is 208 or 240 volts and single phase

50 Amp NEMA 15-50P Power Cord - Unit is a 72" Long Cord with a Four Prong Plug and is used with All Easy-Fire Kilns at any Voltage and 3 Phase Power and All J1800 & JD1800, J23 & JD23, and J230 & JD230 Kilns at any Voltage and 3 Phase Power

15 Amp NEMA 5-15P Power Cord - Unit is a 72" Long Cord and can be used at 120 Volts and 1 Phase Power

Vent-Sure Vent System Power Cord - Unit includes a cord mounted On/Off Switch